The AudioControl EPIC Series Amplifier delivers powerful, heart-pounding bass in a compact, thermally efficient design. Perfectly paired with The Epicenter Bass Restoration Processor (sold separately), it enhances your bass experience to new levels. This amplifier offers exceptional sound quality for the price and is the only AudioControl amplifier to include a bass knob for easy control.

• Digital Class-D Amplifier: Powerful yet compact and stable down to a 1 ohm load.

• 0-12dB Variable Bass Boost Q: Selects the frequency to boost

• Direct Wire Terminals with Hex Screws: Provide solid, reliable connections.

• 4-Gauge Power Terminal and 8-Gauge Speaker Terminal: Designed for maximum current flow.

• 91dB+ Signal-to-Noise Ratio (@ CEA Standard): Ultra-efficient idle draw (< 0.5-1A).

• Smart Auto Reset Protection Circuit: Multiple protection modes are in place to prevent damage if your amplifier encounters an issue.

  • Output Over-Current Protection (OCP)

  • Input Over-Voltage Protection (OVP)

  • Input Under-Voltage Protection (UVP)

  • Output DC-Offset Protection (DCP)

  • Over-Temperature Protection (OTP)

• THE EPICENTER LINK: Simplify your install by connecting the EPIC amplifier directly to an EPICENTER bass restoration processor.

FEATURES

• Compact High-Power Class D Monoblock Amplifier

• High-Current Design – 1Ω Stable

• Smart Auto-Reset Protection Circuit

• 12 dB/octave Linkwitz-Riley Variable Low Pass Filter

• 12 dB/octave Variable Subsonic Filter

• EPICBoost™ Variable Frequency Bass Boost

• ACR-E Remote Level Control Included

• Solid Power/Speaker Terminals with Hex Screws

• Built for THE EPICENTER®

SPECIFICATIONS

INPUTS

• Line-Level Inputs: 500mV – 12V RMS

OUTPUTS

• Continuous Power (RMS) @ 14.4V

  • 1 x 300 Watts @ 4 ohms

  • 1 x 500 Watts @ 2 ohms

  • 1 x 750 Watts @ 1 ohm

  • 1 x 1500 Watts @ 2 ohms Bridged (Strapped)

Remote Level Control

• Included

WEIGHTS & DIMENSIONS

• DIMENSIONS: 6.1″ W x 8.62″ L x 2.01″ H

PERFORMANCE

• Frequency Response (+/- 1 dB): 10 Hz – 190 Hz

• S/N Ratio: 92.2 dBa, Ref 300 Watts @ 4 ohms

• Power / Ground Wire Gauge: 4 AWG

• Recommended Fuse Rating: 80 Amps

• Low Pass Filter: 12dB/octave Linkwitz-Riley, 40 Hz to 180 Hz

• Subsonic Filter: 12 dB/octave Linkwitz-Riley, Off to 50 Hz

• EPIC Boost: Frequency Center: 30 Hz to 80 Hz, Gain: 0 to 12 dB

• Speaker Terminal Wire Gauge: 8 AWG

• Strapable: Yes

• Epicenter Link: Yes

IN THE BOX: EPIC750, Wrench, Screws, ACR-E Remote Level Control and Cable, The Epicenter Link (1m Harness), Manual, Warranty

The AudioControl EPIC Series Amplifier delivers powerful, heart-pounding bass in a compact, thermally efficient design. Perfectly paired with The Epicenter Bass Restoration Processor (sold separately), it enhances your bass experience to new levels. This amplifier offers exceptional sound quality and is the only AudioControl amplifier to include a bass knob for easy control.

• Digital Class-D Amplifier: Powerful yet compact and stable down to a 1 ohm load.

• 0-12dB Variable Bass Boost Q: Selects the frequency to boost

• Direct Wire Terminals with Hex Screws: Provide solid, reliable connections.

• 4-Gauge Power Terminal and 8-Gauge Speaker Terminal: Designed for maximum current flow.

• 91dB+ Signal-to-Noise Ratio (@ CEA Standard): Ultra-efficient idle draw (< 0.5-1A).

• Smart Auto Reset Protection Circuit: Multiple protection modes are in place to prevent damage if your amplifier encounters an issue.

  • Output Over-Current Protection (OCP)

  • Input Over-Voltage Protection (OVP)

  • Input Under-Voltage Protection (UVP)

  • Output DC-Offset Protection (DCP)

  • Over-Temperature Protection (OTP)

• THE EPICENTER LINK: Simplify your install by connecting the EPIC amplifier directly to an EPICENTER bass restoration processor.

FEATURES

• Compact High-Power Class D Monoblock Amplifier

• High-Current Design – 1Ω Stable

• Smart Auto-Reset Protection Circuit

• 12 dB/octave Linkwitz-Riley Variable Low Pass Filter

• 12 dB/octave Variable Subsonic Filter

• EPICBoost™ Variable Frequency Bass Boost

• ACR-E Remote Level Control Included

• Solid Power/Speaker Terminals with Hex Screws

• Built for THE EPICENTER®

SPECIFICATIONS

INPUTS

• Line-Level Inputs: 500mV – 12V RMS

OUTPUTS

• Continuous Power (RMS) @ 14.4V

  • 1 x 400 Watts @ 4 ohms

  • 1 x 700 Watts @ 2 ohms

  • 1 x 1000 Watts @ 1 ohm

  • 1 x 2000 Watts @ 2 ohms Bridged (Strapped)

Remote Level Control

• Included

WEIGHTS & DIMENSIONS

• DIMENSIONS: 6.1″ W x 9.41″ L x 2.01″ H

PERFORMANCE

• Frequency Response (+/- 1 dB): 10 Hz – 190 Hz

• S/N Ratio: 92.1 dBa, Ref 400 Watts @ 4 ohms

• Power / Ground Wire Gauge: 4 AWG

• Recommended Fuse Rating: 100 Amps

• Low Pass Filter: 12dB/octave Linkwitz-Riley, 40 Hz to 180 Hz

• Subsonic Filter: 12 dB/octave Linkwitz-Riley, Off to 50 Hz

• EPIC Boost: Frequency Center: 30 Hz to 80 Hz, Gain: 0 to 12 dB

• Speaker Terminal Wire Gauge: 8 AWG

• Strapable: Yes

• Epicenter Link: Yes

IN THE BOX: EPIC1000, Wrench, Screws, ACR-E Remote Level Control and Cable, The Epicenter Link (1m Harness), Manual, Warranty

The AudioControl EPIC Series Amplifier delivers powerful, heart-pounding bass in a compact, thermally efficient design. Perfectly paired with The Epicenter Bass Restoration Processor (sold separately), it enhances your bass experience to new levels. This amplifier offers exceptional sound quality for the price and is the only AudioControl amplifier to include a bass knob for easy control.

• Digital Class-D Amplifier: Powerful yet compact and stable down to a 1 ohm load.

• 0-12dB Variable Bass Boost Q: Selects the frequency to boost

• Direct Wire Terminals with Hex Screws: Provide solid, reliable connections.

• 4-Gauge Power Terminal and 8-Gauge Speaker Terminal: Designed for maximum current flow.

• 91dB+ Signal-to-Noise Ratio (@ CEA Standard): Ultra-efficient idle draw (< 0.5-1A).

• Smart Auto Reset Protection Circuit: Multiple protection modes are in place to prevent damage if your amplifier encounters an issue.

  • Output Over-Current Protection (OCP)

  • Input Over-Voltage Protection (OVP)

  • Input Under-Voltage Protection (UVP)

  • Output DC-Offset Protection (DCP)

  • Over-Temperature Protection (OTP)

• THE EPICENTER LINK: Simplify your install by connecting the EPIC amplifier directly to an EPICENTER bass restoration processor.

FEATURES

• Compact High-Power Class D Monoblock Amplifier

• High-Current Design – 1Ω Stable

• Smart Auto-Reset Protection Circuit

• 12 dB/octave Linkwitz-Riley Variable Low Pass Filter

• 12 dB/octave Variable Subsonic Filter

• EPICBoost™ Variable Frequency Bass Boost

• ACR-E Remote Level Control Included

• Solid Power/Speaker Terminals with Hex Screws

• Built for THE EPICENTER®

SPECIFICATIONS

INPUTS

• Line-Level Inputs: 500mV – 12V RMS

OUTPUTS

• Continuous Power (RMS) @ 14.4V, <1% THD

  • 1 x 250 Watts @ 4 ohms

  • 1 x 350 Watts @ 2 ohms

  • 1 x 500 Watts @ 1 ohm

  • 1 x 1000 Watts @ 2 ohms Bridged (Strapped)

Remote Level Control

• Included

WEIGHTS & DIMENSIONS

• DIMENSIONS: 6.1″ W x 5.9″ L x 2.01″ H

PERFORMANCE

• Frequency Response (+/- 1 dB): 10 Hz – 190 Hz

• S/N Ratio: 94 dBa, Ref 400 Watts @ 4 ohms

• Power / Ground Wire Gauge: 4 AWG

• Recommended Fuse Rating: 80 Amps

• Low Pass Filter: 12dB/octave Linkwitz-Riley, 40 Hz to 180 Hz

• Subsonic Filter: 12 dB/octave Linkwitz-Riley, Off to 50 Hz

• EPIC Boost: Frequency Center: 30 Hz to 80 Hz, Gain: 0 to 12 dB

• Speaker Terminal Wire Gauge: 8 AWG

• Strapable: Yes

• Epicenter Link: Yes

IN THE BOX: EPIC500, Wrench, Screws, ACR-E Remote Level Control and Cable, The Epicenter Link (1m Harness), Manual, Warranty

The AudioControl EPIC Series 4-Channel Amplifier delivers top-quality sound in a compact, thermally efficient design. Engineered with a high-current Class D design, it’s 2Ω stable, ensuring maximum power output while maintaining efficiency. With a smart auto-reset protection circuit and solid power/speaker terminals secured by hex screws, the EPIC Series amplifier offers reliable, exceptional sound quality in a rugged, space-saving package. The EPICBIGFOUR is designed to deliver massive power at 1400W RMS.

• Digital Class-D Amplifier: Powerful yet compact, designed to handle 2 ohm loads for high output.

• Direct Wire Terminals with Hex Screws: Provide solid, reliable connections.

• 4-Gauge Power Terminal and 8-Gauge Speaker Terminal: Designed for maximum current flow.

• 89dB+ Signal-to-Noise Ratio (@ CEA Standard): Ultra-efficient idle draw (< 0.5-1A).

• Smart Auto Reset Protection Circuit: Multiple protection modes are in place to prevent damage if your amplifier encounters an issue.

  • Output Over-Current Protection (OCP)

  • Input Over-Voltage Protection (OVP)

  • Input Under-Voltage Protection (UVP)

  • Output DC-Offset Protection (DCP)

  • Over-Temperature Protection (OTP)

• EPICENTER Link: Compatible with The EPICENTER bass restoration processor.

FEATURES

• Compact High-Power Class D Amplifier

• High-Current Design – 2Ω Stable

• 4 x 200 Watts @ 4 ohms

• 4 x 350 Watts @ 2 ohms

• 2 x 650 Watts @ 4 ohms Bridged

• Smart Auto-Reset Protection Circuit

• 12 dB/octave Linkwitz-Riley Variable High Pass & Low Pass Filters

• Solid Power/Speaker Terminals with Hex Screws

• ACR-E Remote Bass Knob Included

SPECIFICATIONS

INPUTS

• Line-Level Inputs: 500mV – 12V RMS

OUTPUTS

• Continuous Power (RMS) @ 14.4V

  • 4 x 200 Watts @ 4 ohms

  • 4 x 350 Watts @ 2 ohms

  • 2 x 650 Watts @ 4 ohms Bridged

WEIGHTS & DIMENSIONS

• DIMENSIONS: 6.1″ W x 10.56″ L x 2.01″ H

PERFORMANCE

• Frequency Response (+/- 1 dB): 10 Hz – 22 kHz

• S/N Ratio: 89 dBa, Ref 200 Watts @ 4 ohms

• Power / Ground Wire Gauge: 4 AWG

• Recommended Fuse Rating: 150 Amps

• High Pass Filter: 12dB/octave Linkwitz-Riley, Off, 50 Hz to 5000 Hz

• Low Pass Filter: 12dB/octave Linkwitz-Riley, Off, 50 Hz to 5000 Hz

• Speaker Terminal Wire Gauge: 8 AWG

IN THE BOX: EPICBIGFOUR, Wrench, Screws, ACR-E Remote Level Control & Cable, Manual, Warranty

The AudioControl EPIC Series 6-Channel 1200 Watt RMS Amplifier is a compact, full range class D amplifier engineered for flexibility, output, and reliability. Its high-current design delivers serious performance, while the Smart Auto-Reset Protection Circuit keeps everything running smoothly, even under demanding conditions.

Built for those who demand options—active 3-way front stage, 5-channel, active 6-channel, or a powerful bridged configuration. Whatever your design calls for, EPICSIX fits the plan and delivers. One amplifier delivers so many possibilities, giving you the freedom to build, tune and evolve your system, not limit it.

This crossover configuration ensures proper frequency distribution, improved sound clarity, and reliable speaker protection, while offering exceptional flexibility for a wide range of system designs. With adjustable high-pass and low-pass filters across multiple channels, EPICSIX allows precise tuning for active or passive setups, making it easy to adapt the amplifier to your design.

FEATURES

• Compact High-Power Class D Amplifier
• High-Current Design, 2 ohms Stable
• 6 x 100 Watts @ 4 ohms
• 6 x 200 Watts @ 2 ohms
• 2 x 400 Watts @ 4 ohms Bridged (Ch. 3/4 & 5/6)
• Smart Auto-Reset Protection Circuit
• 12 dB/octave Linkwitz-Riley Variable High Pass (Ch 1-6) & Low Pass Filters (Ch 3-6)
• Solid Power/Speaker Terminals with Hex Screws

SPECIFICATIONS

INPUTS

• Line-Level Inputs: 500mV – 12V RMS

OUTPUTS

• Continuous Power (RMS) @ 14.4V, <1% THD

  • 6 x 100 Watts @ 4 ohms

  • 6 x 200 Watts @ 2 ohms

  • 2 x 400 Watts @ 4 ohms Bridged

WEIGHTS & DIMENSIONS

• DIMENSIONS (WxLxH): 6.1″ x 12.56″ x 2.01″ / 155mm x 319mm x 51mm

PERFORMANCE

• Frequency Response (+/- 3 dB): 10 Hz – 24 kHz

• S/N Ratio: 98 dBa, Ref 100 Watts @ 4 ohms

• Power / Ground Wire Gauge: 4 AWG

• Recommended Fuse Rating: 125 Amps

• High Pass Filter: 12dB/octave Linkwitz-Riley, Off, 50 Hz to 5000 Hz

• Low Pass Filter: 12dB/octave Linkwitz-Riley, 50 Hz to 5000 Hz

• Speaker Terminal Wire Gauge: 10 AWG

IN THE BOX: EPICSIX Amplifier, Wrench, Screws, Manual

California Proposition 65

The KEY500.1 is a smart subwoofer amplifier and audio processor in one, featuring an AI-driven DSP (digital signal processing).

AUTO EQ

Using KICKER’s supplied test tones (below), the KEY automatically analyzes the audio being fed into the amplifier. Once this signal has been analyzed, the amp will automatically fix peaks in the signal coming in and restore the low bass that is typically missing. In a matter of moments, you get a clean, even bass response from your amp!

Start with these FREE TEST TONES for easy setup!

ALL THE CONTROL

Craft your sound with ease! The KEY500.1 comes with 24dB sub-sonic and low-pass crossovers, bass boost and gain controls.

HIDDEN TREASURE

Measuring about eight inches long and less than two inches high, the KEY500.1 fits nearly anywhere. Mount it behind your glove box, under the seat, or in your trunk with ease.

START. DON’T STOP.

The amplifier also features FIT+™ (Fail-safe Integration Technology PLUS) – which provides nearly universal compatibility with stock or aftermarket radios. Another industry first, the KEY500.1 is uniquely suited to accept factory input signals as high as 40 volts (400 watts). The KEY amplifier will work with almost every car on the road today, whether you have a factory or aftermarket audio system.

SUGGESTED ENCLOSURES

While we suggest this list for the ultimate bass experience, KEY500.1 will actually work with all KICKER subwoofers up to 12 inches; see your sales associate for the ideal subwoofer in your particular system, because every system is unique.

4Ω = 150 Watts RMS
2Ω = 300 Watts RMS
1Ω = 500 Watts RMS

VCVR122
TCWRT82
TCWRT102
TCWRT122
TL7T122
TL7T102
TL7T82
CWTB102
CWTB82
TL7R102
TL7S102
TRTP122
TRTP102
TRTP82
CVTDF122
CVTDF102

Remote Control

Your KEY500.1 amplifier is compatible with the CXARC remote control. Use it to customize your bass on the fly with just a turn of a knob!

If you have two mono amps or powered subwoofers, check out the DBRC Remote for controlling both from the same knob.

Specifications

White Paper 47KEY5001-wp.pdf Power (watts/ch), 1 Ohm mono500 Power (watts/ch), 2 Ohm mono300 Power (watts/ch), 4 Ohm mono150 Standard dimensions in.(H x W x L)1-11/16 x 4-1/8 x 8-1/8 Metric dimensions cm(H x W x L)4.3 x 9.2 x 20.7 Frequency Response (Hz):10-160

Input Sensitivity:high level: 1V-40V / low level: 125mV-5V Signal-to-Noise Ratio:>90dB, a-weighted, re: rated power Selectable Electronic Crossover:Variable Low Pass 40-160 Hz, Variable High Pass 10-40 Hz Warranty When purchased from an Authorized KICKER Dealer or kicker.com, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase.

The biggest advance - in the smallest package.
Introducing the KEY smart amplifier and audio processor in one, featuring AI-driven DSP.

Pasmag Reviews the Key Smart Amplifier

Designed specifically to greatly improve the sonics of a typical “deck and four” or OEM sort of system, the Kicker KEY amplifier uses powerful digital signal processing to bring concert realism to your car. Read the full review here.

Hear what the other reviewers have to say about this product! Read the reviews here.

ACOUSTIC CORRECTION = AUDIO PERFECTION

Don't just make your system louder - make it clearer. Make it better…

Press the selector, and the microphone goes to work. The KEY uses a powerful internal computer to deliver dramatic improvements in realism and soundstage. A massive 40-band equalizer improves tonality, and a 24dB crossover re-defines the capabilities of each speaker.

The concert quality of your factory stereo is revealed! What would take hours for a professional to achieve happens in a matter of minutes. All automatically. All with the press of a single button.

Start with these FREE TEST TONES for easy setup!

POWERHOUSE

In addition to an unbelievable sound quality, the KEY200.4 delivers 200 watts of pumpin' power to your factory speakers. At KICKER, we know power and clarity always go hand-in-hand.

HIDDEN TREASURE

Measuring less than eight inches long and only two inches high, the KEY200.4 fits nearly anywhere. Mount it behind your radio, under the seat, or in your trunk with ease.

START. DON'T STOP.

The KEY200.4 is one of the first amps fully compatible with newer vehicles using start-stop systems. The amplifier also features FIT2™ (Fail-Safe Integration Technology), providing compatibility with nearly every stock and aftermarket radio on the road today.

KEEP THE BEAT

If the temperature reaches the threshold, the KEY200.4's dynamic power-management algorithms kick into gear! Instead of hearing the amplifier's volume “pumping” or blowing a fuse – KEY technology engages a nearly inaudible limiter/compressor, applied only to the peaks of the music for as little as milliseconds at a time. The amplifier quickly cools, which deactivates the compressor. Music returns to its full dynamic range without a moment’s interruption!

DETAILS, DETAILS

• 200 Watts Of Power (50x4)

• Auto EQ Microphone With Selector Switch Included

• Compatible with Start/Stop Vehicle Technology

• FIT2™ Technology Included

• Turn On Via Remote 12v Signal Or DC Offset

• Auto 40-Band Equalizer

• Bi-Amp Capability (Defeatable)

• Auto Compressor (Defeatable)

• Kicker EQ Preset (Defeatable)

• Auto Time Alignment (Defeatable)

• Auto Level Adjustment (Bi-Amp Mode Only)

• Auto Speaker Size Detection

• 24dB Crossovers

• 60/80/120hz High Pass Filter (Defeatable)

• Specifications

  White Paper 47KEY2004-wp.pdf Power (watts/ch), 4 Ohm stereo 50x 4 Microphone/Kicker EQ button included Standard dimensions (H x W x L) 1-11/16 x 2-3/4 x 7-3/8 Metric dimensions (H x W x L)4.3 x 7 x18.7 Frequency Response (Hz):20-20k, +0/-1dB

  Input Sensitivity:high level 250mV-10V Signal-to-Noise Ratio: >90dB, a-weighted, re: rated power Active Crossover:Off, 60, 80, or 120 Hz; 24dB/octave

• What's in the Box:

  1 - 4 channel power amplifier
  1 - microphone
  1 - microphone cable with switch
  1 - fuse holder
  1 - manual and installation hardwareWarrantyWhen purchased from an Authorized KICKER Dealer or kicker.com, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase.

The Warhorse WXA1000.4 provides 2000 watts of dynamic power while still maintaining complete reliability under this intense power use.

Full-Range Riot

• Engineered completely in-house by KICKER R&D

• Features extreme reliability under intense power and overall use

• Ultra-efficient, half-bridge Class-D design

• Fully start/stop compliant – operational to 6.5V

• 1/0 Power and Ground inputs to ensure you get the power you paid for

• Capable of daisy-chaining remote power across multiple amps

• Includes a heavy-duty, magnetic-mount diagnostic tool for monitoring voltage measurements and amp protection status – 19.75 feet (6m) RJ45 cable

• Fully compatible with most factory or aftermarket source units (with FIT+™ differential inputs)

• WARHORSE Install Scenarios: WarhorseInstallScenariosv2.pdf

• REMOTE/DIAGNOSTIC TOOL SURFACE MOUNT TEMPLATE

• REMOTE/DIAGNOSTIC TOOL FLUSH MOUNT TEMPLATE

• Specifications

  MODEL WXA1000.4 WARHORSE 1000.4 white paper with full tech graph data 49WXA10004 Whitepaper PDF WARHORSE 1000.4 Dimensions 49WXA10004 Product Dimensions PDF* RMS Power (watts/ch) 2 Ohm Stereo (@14.4V, <1% THD)450x4* RMS Power (watts/ch) 4 Ohm Stereo (@14.4V, <1% THD)250x4* RMS Power (watts/ch) 4 Ohm Bridged Mono (@14.4V, <1% THD)900x2** Dynamic Power (watts)2000 Frequency Response (Hz)10-20k Signal-to-Noise Ratio (dB; A-weighted, re: rated power)>90 Signal-to-Noise Ratio (dB; ref: 1W output)>70Input Sensitivity low level 125mV-5V high level 1V-40V Selectable Electronic Crossover - AMP 1Off/HP/LP; 24dB/octave BW, variable 10-5kHz w/ 10X switch; Selectable Electronic Crossover - AMP 2Off/HP/LP/BP; 24dB/octave BW, lo-pass 100-5000Hz, hi-pass 10-500Hz Dimensions (in, cm)H – 2-9/16, 6.5
  W – 9-1/8, 23.2 L – 15-3/8, 39.1

• Warranty When purchased from an Authorized KICKER Dealer or kicker.com, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase.

The Warhorse WXA3600.1 was engineered completely in-house by KICKER Research and Development for ultra-high SPL applications.

Not your Average Amp

• Features extreme reliability under intense bass power and overall use

• Engineered completely in-house by KICKER R&D

• Full-bridge Class-D design

• Quad micro-controller-regulated cooling fans

• Capable of daisy-chaining remote power across multiple amps

• Competition mode switch to avoid potentiometer creep, fix crossover setting, and gain-match multiple amps

• Includes premium remote bass-level control with a magnetic mount – 19.75 feet (6m) RJ45 cable

• Includes a heavy-duty, magnetic-mount diagnostic tool for monitoring voltage measurements and amp protection status – 19.75 feet (6m) RJ45 cable

• Fully compatible with most factory or aftermarket source units (with FIT+™ differential inputs)

• WARHORSE Install Scenarios: WarhorseInstallScenariosv2.pdf

• REMOTE/DIAGNOSTIC TOOL SURFACE MOUNT TEMPLATE

• REMOTE/DIAGNOSTIC TOOL FLUSH MOUNT TEMPLATE

• Specifications

  MODEL WXA3600.1 WARHORSE 3600.1 white paper with full tech graph data49WXA36001 Whitepaper PDF WARHORSE 3600.1 Dimensions 49WXA36001 Product Dimensions PDF RMS Power (watts/ch) 1 Ohm Mono (@ 14.4v, <1%THD)3600x1* RMS Power (watts/ch) 2 Ohm Mono (@ 14.4v, <1%THD)2500x1* RMS Power (watts/ch) 4 Ohm Mono (@ 14.4v, <1%THD)1400x1** Dynamic Power (watts)5000 Frequency Response (Hz)10-200 Signal-to-Noise Ratio (dB; A-weighted, re: rated power)>90

  Signal-to-Noise Ratio (dB; ref: 1W output)>70 Input Sensitivity low level 125mV-5V
  high level 1V-40V Selectable Electronic Crossover Variable Low-pass 50-200Hz, 24dB/octave Subsonic Filter Defeatable @ 15Hz, 24dB/octave Competition Mode warhorse-competition-mode.pdf Dimensions (in, cm)H – 2-9/16, 6.5
  W – 9-1/8, 23.2 L – 15-3/8, 39.1

• Warranty When purchased from an Authorized KICKER Dealer or kicker.com, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase.

If you have two mono amps or powered subwoofers, check out the DBRC Remote for controlling both from the same knob.

CX-Series amps reach massive power levels thanks to an optimized circuit layout and the highest-grade internal components. Highly efficient heat sinks keep the amp cool with a sophisticated look. Mono amps offer an optional remote level control to adjust your bass right from the dash.

• Efficient Class-D amplifier

• Three-second turn-on/off delay to eliminate unwanted interference

• Variable 12dB crossovers provides control to dial in perfect sound

• KickEQ™ 6dB variable bass boost for those additional low frequencies

• 24dB subsonic filter for protection from potentially damaging frequencies

• FIT+™ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio

• Accepts up to 40-volt input signal

• Small footprint for easier installation

• Compatible with CXARC Remote Bass Control

• Vertical mounting hardware included for another unique look

• Power Pack

  This CX-Series Mono Amp is now one-ohm stable, giving you even more power and wiring options for your system! This Class-D CXA400.1 features a variable bass boost with KickEQ™, giving you as much as a 6dB of extra bump. A powerful 12dB crossover and 24dB subsonic filter is included, letting you quickly tune your system to perfection. Use the full-range outputs to expand your system with other bass amps, or a full-range amp to complete your system. From your dash, a simple turn of the optional CXARC Remote Bass Controller (sold separately) increases your output to fit your choice of music.

  CX.1 Amplifiers accept up to 40 volts (400 watts) of speaker-level input signal. This kind of flexibility both makes line-out converters unnecessary and optimizes your sound quality at the same time!

  Expand your system with full-range, RCA pass-through outputs, then choose a “standard” mount or a cool vertical mount with the included hardware.

  CX.1 Amps deliver as much as 400 watts into one bass channel. See below for more details.

• Specifications

  MODEL CXA400.1 Power (watts/ch) 4 Ohm150x1 Power (watts/ch) 2 Ohm300x1 Power (watts/ch) 1 Ohm400x1 CXRC Remote Bass Capable (sold sep.)yes Dimensions (in, cm): (all models 2-3/8, 5.9H x 6-3/4, 17W x ...L)8-1/8, 20.6 Frequency Response (Hz):25-200, +0/-1dB

  Input Sensitivity:125mV–5V (Low Level) White Paper46CXA4001-wp.pdf
  1V–40V (High Level) Signal-to-Noise Ratio:>95dB, a-weighted, re: rated powerActive Crossover:Variable Lo-pass 50Hz–200Hz, 12dB/octave Subsonic Filter:25Hz @24dB/octave KickEQ™ Boost Variable 0-6dB @40Hz Warranty When purchased from an Authorized KICKER Dealer or kicker.com, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase.

If you have two mono amps or powered subwoofers, check out the DBRC Remote for controlling both from the same knob.

CX-Series amps reach massive power levels thanks to an optimized circuit layout and the highest-grade internal components. Highly efficient heat sinks keep the amp cool and an optional remote level control lets you adjust bass on the fly.

• Class A/B full-range channels

• Class D bass channel included for one amp to run an entire system

• Three-second turn-on/off delay to eliminate unwanted interference

• Variable 12dB crossovers provides control to dial in perfect sound

• KickEQ™ 6dB variable bass boost for those additional low frequencies

• 24dB subsonic filter for protection from potentially damaging frequencies

• FIT+™ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio

• Accepts up to 40-volt input signal

• Small footprint for easier installation

• Vertical mounting hardware included for another unique look

• Five Channels of Fun

  The CXA660.5 Amplifier is built to be the complete package in one cool-looking amp.

  This CX amplifier uses powerful Class A/B technology to power four mid/high-range channels and an ultra-efficient Class D power plant for the bass channel. The amp also comes equipped with FIT+™ (Fail-safe Integration Technology-PLUS), giving you superior clarity and dependability.

  KickEQ™ variable bass boost gives you as much as a 6dB of extra bump. A powerful 12dB crossover and 24dB subsonic filter is also included, letting you quickly tune your entire system to taste. From your dash, a simple turn of the optional CXARC Remote Bass Controller (sold separately) increases your output to fit your choice of music.

  This CX amplifier delivers as much as 90 watts into four full-range channels or 180 watts into two-bridged channels, plus as much as 300 watts into one bass channel. See below for more details.

• Specifications

  MODEL CXA660.5 Power (watts/ch) 4 Ohm Stereo65x4 Power (watts/ch) 2 Ohm Stereo90x4 Power (watts/ch) 4 Ohm Stereo180x2 Power (watts/ch) 4 Ohm Mono Sub Ch150x1 Power (watts/ch) 2 Ohm Mono Sub Ch300x1 CXRC Remote Bass Capable (sold sep.)yes Dimensions (in, cm): (all models 2-3/8, 5.9H x 6-3/4, 17 W x ...L)14-1/8, 35.7 Frequency Response (Hz):10Hz-20kHz Frequency Response (Hz – Sub Ch.):25Hz-200Hz

  Input Sensitivity:125mV–5V (Low Level) White Paper46CXA6605-wp.pdf
  1V–40V (High Level) Signal-to-Noise Ratio:90dB Active Crossover:Amp 1-2: High Pass 10-200Hz @ 12dB/Octave
  Sub Channel: Low Pass 50-200Hz @ 12dB/Octave Subsonic Filter:25Hz @24dB/Octave KickEQ™ BoostVariable 0-6dB @40Hz Warranty When purchased from an Authorized KICKER Dealer or kicker.com, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase.

If you have two mono amps or powered subwoofers, check out the DBRC Remote for controlling both from the same knob.

CX-Series Amps reach massive power levels thanks to an optimized circuit layout and the highest-grade internal components. Highly efficient heat sinks keep the amp cool with a sophisticated new look. Mono amps offer an optional remote level control to adjust your bass right from the dash.

• Efficient Class-D amplifier

• Three-second turn-on/off delay to eliminate unwanted interference

• Variable 12dB crossovers provides control to dial in perfect sound

• KickEQ™ 6dB variable bass boost for those additional low frequencies

• 24dB subsonic filter for protection from potentially damaging frequencies

• FIT+™ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio

• Accepts up to 40-volt input signal

• Small footprint for easier installation

• Compatible with CXARC Remote Bass Control

• Vertical mounting hardware included for another unique look

• Power Station

  The CXA1800.1 Mono Amplifier is built for big bass in a sleek, yet affordable package. Using a Class-D power package and FIT+™ (Fail-safe Integration Technology-PLUS) for superior dependability, this amp features a variable bass boost with KickEQ™, giving you as much as a 6dB of extra bump. From your dash, a simple turn of the optional CXARC Remote Bass Controller (sold separately) increases your output to fit your choice of music.

  CX-Series Amplifiers accept up to 40 volts (400 watts) of speaker-level input signal. This kind of flexibility both makes line-out converters unnecessary and optimizes your sound quality at the same time!

  A powerful 12dB crossover and 24dB subsonic filter is included, letting you quickly tune your system to perfection. Use the full range outputs to expand your system with other bass amps, or add a full range amp to complete your system.

  This CX-Series Amplifier delivers as much as 1,800 watts into one bass channel. See below for more details.

• Specifications

  MODEL CXA1800.1 Power (watts/ch) 4 Ohm900x1 Power (watts/ch) 2 Ohm1800x1 Power (watts/ch) 1 Ohm1800x1 +/-10% CXRC Remote Bass Capable (sold sep.)yes Dimensions (in, cm): (all models 2-3/8, 5.9H x 6-3/4, 17W x ...L) 14-3/8, 36.4 Frequency Response (Hz):25-200Hz

  Input Sensitivity:125mV–5V (Low Level) 1V–40V (High Level) White Paper46CXA18001-wp.pdf Signal-to-Noise Ratio:95dB Active Crossover:Variable Lo-pass 50Hz–200Hz, 12dB/octave Subsonic Filter:25Hz @24dB/octave KickEQ™ BoostVariable 0-6dB @40Hz Warranty When purchased from an Authorized KICKER Dealer or kicker.com, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase.

If you have two mono amps or powered subwoofers, check out the DBRC Remote for controlling both from the same knob.

CX-Series mono amps offer an optional remote level control to adjust your bass right from the dash. Dial it up the way you want to hear it.

CXARC Remote

Customize your bass, right from your front seat.

The CXARC is a remote bass controller, compatible with the KEY500.1 and Hideaway, and any CX, DX or PX KICKER amplifier equipped with a REMOTE BASS jack on its end.

Cable Length - 19.75 feet

The CXA1200.1 Mono Amplifier is built for affordable power and performance, thanks to an optimized circuit layout and the high-grade internal components.

• Efficient Class-D amplifier

• Three-second turn-on/off delay to eliminate unwanted interference

• Variable 12dB crossovers provides control to dial in perfect sound

• KickEQ™ 6dB variable bass boost for those additional low frequencies

• 24dB subsonic filter for protection from potentially damaging frequencies

• FIT+™ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio

• Accepts up to 40-volt input signal

• Small footprint for easier installation

• Compatible with CXARC Remote Bass Control

• Vertical mounting hardware included for another unique look

• Mono Monster

  This mono CX-Series Amp is now one-ohm stable, giving you even more wiring options for your system! The Class-D CXA1200.1 features a variable bass boost with KickEQ™, giving you as much as a 6dB of extra bump. A powerful 12dB crossover and 24dB subsonic filter is included, letting you quickly tune your system to perfection. From your dash, a simple turn of the optional CXARC Remote Bass Controller (sold separately) increases your output to fit your choice of music.

  CX-Series Amplifiers accept up to 40 volts (400 watts) of speaker-level input signal. This kind of flexibility both makes line-out converters unnecessary and optimizes your sound quality at the same time!

  Use the full-range outputs to expand your system with other bass amps, or add a full-range amp to complete your system.

  This CX.1 Amplifier delivers as much as 1,200 watts into one bass channel. See below for more details.

• Specifications

  MODEL CXA1200.1 Power (watts/ch) 4 Ohm600x1 Power (watts/ch) 2 Ohm1200x1 Power (watts/ch) 1 Ohm1200x1 +/-10% CXRC Remote Bass Capable (sold sep.)yes Dimensions (in, cm): (all models 2-3/8, 5.9H x 6-3/4, 17W x ...L)12, 30.6 Frequency Response (Hz):25-200Hz

  Input Sensitivity:125mV–5V (Low Level) White Paper46CXA12001-wp.pdf
  1V–40V (High Level) Signal-to-Noise Ratio:95dB Active Crossover:Variable Lo-pass 50Hz–200Hz, 12dB/octave Subsonic Filter:25Hz @24dB/octave KickEQ™ Boost Variable 0-6dB @40Hz Warranty When purchased from an Authorized KICKER Dealer or kicker.com, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase.

If you have two mono amps or powered subwoofers, check out the DBRC Remote for controlling both from the same knob.

The CXA800.1 Mono Amplifier is built for affordable power and performance, thanks to optimized circuit layout and high-grade internal components.

• Efficient Class-D amplifier

• Three-second turn-on/off delay to eliminate unwanted interference

• Variable 12dB crossovers provides control to dial in perfect sound

• KickEQ™ 6dB variable bass boost for those additional low frequencies

• 24dB subsonic filter for protection from potentially damaging frequencies

• FIT+™ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio

• Accepts up to 40-volt input signal

• Small footprint for easier installation

• Compatible with CXARC Remote Bass Control

• Vertical mounting hardware included for another unique look

• About That Power

  This CX-Series Mono Amp is now one-ohm stable, giving you even more power and wiring options for your system! This Class-D CXA800.1 features a variable bass boost with KickEQ™, giving you as much as a 6dB of extra bump. A powerful 12dB crossover and 24dB subsonic filter is included, letting you quickly tune your system to perfection. Use the full-range outputs to expand your system with other bass amps, or a full-range amp to complete your system. From your dash, a simple turn of the optional CXARC Remote Bass Controller (sold separately) increases your output to fit your choice of music.

  CX-Series Amplifiers accept up to 40 volts (400 watts) of speaker-level input signal. This kind of flexibility both makes line-out converters unnecessary and optimizes your sound quality at the same time!

  Expand your system with full-range, RCA pass-through outputs, then choose a “standard” mount or a cool vertical mount with the included hardware.

  This CX.1 amplifier delivers as much as 800 watts into one bass channel. See below for more details.

• Specifications

  MODEL CXA800.1 Power (watts/ch) 4 Ohm300x1 Power (watts/ch) 2 Ohm600x1 Power (watts/ch) 1 Ohm800x1 CXRC Remote Bass Capable (sold sep.)yes Dimensions (in, cm): (all models 2-3/8, 5.9H x 6-3/4, 17W x ...L)8-1/8, 20.6 Frequency Response (Hz):25-200, +0/-1dB

  Input Sensitivity:125mV–5V (Low Level) White Paper 46CXA8001-wp.pdf
  1V–40V (High Level) Signal-to-Noise Ratio:>95dB, a-weighted, re: rated powerActive Crossover:Variable Lo-pass 50Hz–200Hz, 12dB/octave Subsonic Filter:25Hz @24dB/octave KickEQ™ BoostVariable 0-6dB @40Hz Warranty When purchased from an Authorized KICKER Dealer or kicker.com, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase.

If you have two mono amps or powered subwoofers, check out the DBRC Remote for controlling both from the same knob.

The CXA360.4 Four-Channel Amplifier is built to power all your door speakers in a single, powerful package.Class A/B full-range channels

• Flexible and Fun

  Using Class A/B power, this amp features a variable bass boost with KickEQ™, giving you as much as a 6dB of extra bump. A powerful 12dB crossover is also included, letting you quickly tune your system to perfection.

  CX-Series Amplifiers accept up to 40 volts (400 watts) of speaker-level input signal. This kind of flexibility both makes line-out converters unnecessary and optimizes your sound quality at the same time!

  Highly efficient heat sinks keep the amp cool with a sophisticated new look, while KICKER’s FIT+™ (Fail-safe Integration Technology-PLUS), gives you outstanding noise rejection - even with premium factory audio systems.

  This CX-Series Amplifier delivers as much as 90 watts into four full-range channels, or 180 watts into two bridged channels. See below for more details.

• Three-second turn-on/off delay to eliminate unwanted interference

• Variable 12dB crossovers provides control to dial in perfect sound

• KickEQ™ 6dB variable bass boost for those additional low frequencies

• FIT+™ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio

• Accepts up to 40-volt input signal

• Small footprint for easier installation

• Vertical mounting hardware included for another unique look

• Compatible with CXARC Remote Bass Control (AMP2 must be in LO-PASS X-OVER mode)

• Specifications

  MODEL CXA360.4 Power (watts/ch) 4 Ohm Stereo65x4 Power (watts/ch) 2 Ohm Stereo 90x4 Power (watts/ch) 4 Ohm Mono180x2 CXARC Remote Bass Capable (sold sep.)Yes Dimensions (in, cm): (all models 2-3/8, 5.9H x 6-3/4, 17W x ...L) 12-1/2, 31.7 Frequency Response (Hz):10Hz-20kHz

  Input Sensitivity:125mV–5V (Low Level) White Paper46CXA3604-wp.pdf
  1V–40V (High Level) Signal-to-Noise Ratio:95dB Active Crossover:HI, LO or OFF; Variable 50–200Hz @ 12dB/OctaveSubsonic Filter:n/a KickEQ™ BoostVariable 0-6dB @40Hz

• Warranty When purchased from an Authorized KICKER Dealer or kicker.com, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase.

VXA Mono Amplifiers offer a remote level control to adjust your bass right from the dash.Class-D mono channel for lower current draw and longer playing time

Class-Leading Power

• Mono power stable to 1 Ohm for louder bass

• Remote Bass Control for fingertip tuning

• Variable 12dB crossovers for ideal speaker matching

• 24dB subsonic filter for protection from potentially damaging frequencies

• KickEQ™ variable bass boost for louder low frequencies

• KICKER FIT™ (Fail-safe Integration Technology) means it works with nearly every radio

• Small footprint for easy installation

• Compatible with start/stop vehicle technology

• DC-offset automatic turn on

• Class SB-compatible for OEM integration within Class-SB head units

• Power Pack

  The VXA-Series Mono Amp is one-ohm stable, giving you even more power and wiring options for your system! This Class-D VXA1000.1 features a variable bass boost with KickEQ™, giving you as much as a 6dB of extra bump.

• Remote Ready

  VXA-Series Amplifiers with mono channels include the VXARC Remote Bass Knob. Use it to customize your bass on the fly with just a turn of a dial!

• Specifications

  Power (watts/ch), 1 Ohm Mono:1000 x 1 Power (watts/ch), 2 Ohm Mono:750 x 1 Power (watts/ch), 4 Ohm Mono:400 x 1 Dynamic Power (watts):1400Frequency Response (Hz):10-200 (+0/-6dB) VXARC Remote Bass:included Dimensions (in, cm):Height: 2-3/16 (5.6 cm) Width: 5-29/32 (15 cm) Length: 9-1/2 (24.2 cm)

  Input Sensitivity:125mV-10V Signal-to-Noise Ratio:>95dB (A-weighted, re: rated power) Selectable Electronic Crossover:12dB/octave, variable LP 50-200Hz Subsonic Filter:fixed 15Hz, 24dB/octave KickEQ Bass Boost:variable 0-6dB @ 40Hz

• Warranty When purchased from an Authorized KICKER Dealer or kicker.com, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase.

VXA Mono Amplifiers offer a remote level control to adjust your bass right from the dash. Class-D mono channel for lower current draw and longer playing time

Class-Leading Power

• Mono power stable to 1 Ohm for louder bass

• Remote Bass Control for fingertip tuning

• Variable 12dB crossovers for ideal speaker matching

• 24dB subsonic filter for protection from potentially damaging frequencies

• KickEQ™ variable bass boost for louder low frequencies

• KICKER FIT™ (Fail-safe Integration Technology) means it works with nearly every radio

• Small footprint for easy installation

• Compatible with start/stop vehicle technology

• DC-offset automatic turn on

• Class SB-compatible for OEM integration within Class-SB head units

• Power Pack

  The VXA-Series Mono Amp is one-ohm stable, giving you even more power and wiring options for your system!  This Class-D VXA700.1 features a variable bass boost with KickEQ™, giving you as much as a 6dB of extra bump.

• Remote Ready

  VXA-Series Amplifiers with mono channels include the VXARC Remote Bass Knob. Use it to customize your bass on the fly with just a turn of a dial!

• Specifications

  Power (watts/ch), 1 Ohm Mono:700 x 1 Power (watts/ch), 2 Ohm Mono:500 x 1 Power (watts/ch), 4 Ohm Mono:250 x 1 Dynamic Power (watts):900 Frequency Response (Hz):10-200 (+0/-6dB) Dimensions (in, cm):Height: 2-3/16 (5.6 cm) Width: 5-29/32 (15 cm) Length: 8-15/16 (22.7 cm)

  Input Sensitivity:125mV-10V Signal-to-Noise Ratio:>95dB (A-weighted, re: rated power) Selectable Electronic Crossover:12dB/octave, variable LP 50-200Hz Subsonic Filter:fixed 15Hz, 24dB/octave KickEQ Bass Boost:variable 0-6dB @ 40Hz

• Warranty When purchased from an Authorized KICKER Dealer or kicker.com, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase.

The VXA600.5 5-Channel Amplifier is built to power an entire mobile-audio system, including your subwoofer! A VXARC Remote Bass Knob is included to dial in more bass.Class D design for lower current draw and longer playing time

• Bass channel lets one amp run an entire system

• Remote Bass Control included for fingertip tuning (sub channel)

• Variable 12dB crossovers for ideal speaker matching

• 24dB subsonic filter for protection from potentially damaging frequencies

• KickEQ™ variable bass boost for louder low frequencies

• KICKER FIT™ (Fail-safe Integration Technology) means it works with nearly every radio

• Small footprint for easy installation

• Compatible with start/stop vehicle technology

• DC-offset automatic turn on

• Class SB-compatible for OEM integration within Class-SB head units

• Five Channels of Fun

  The VXA600.5 Amplifier is built to be the complete package in one cool-looking amp.
  
  This amplifier uses powerful, ultra-efficient Class-D power for the full-range and mono channels. The amp also comes equipped with FIT™ (Fail-safe Integration Technology), giving you superior clarity and dependability.

• Remote Ready

  VXA-Series Amplifiers with mono channels include the VXARC Remote Bass Knob. Use it to customize your bass on the fly with just a turn of a dial!

• Specifications

  Power (watts/ch), 2 Ohm Stereo:75 x 4 Power (watts/ch), 4 Ohm Stereo:50 x 4 Power (watts/ch), 4 Ohm Bridged Mono:150 x 2 Power (watts/ch), 2 Ohm Mono:300 x 1 Power (watts/ch), 4 Ohm Mono:150 x 1 Dynamic Power (watts):750 Frequency Response (Hz):Amp1/2 10-20k (+0/-1dB); Sub 10-200 (+0/-6dB) Dimensions (in, cm):Height: 2-3/16 (5.6 cm) Width: 5-29/32 (15 cm) Length: 11-5/32 (28.3 cm) Input Sensitivity:125mV-10V Signal-to-Noise Ratio:Amp1/2 >95dB (A-weighted, re: rated power); Selectable Electronic Crossover:12dB/octave, AMP1/2: variable HP 10-200Hz; SUB: variable LP 50-200Hz Subsonic Filter (sub ch only):fixed 15Hz, 24dB/octave KickEQ Bass Boost (sub ch only):variable 0-6dB @ 40Hz

• Warranty When purchased from an Authorized KICKER Dealer or kicker.com, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase.

The VXA300.4 Four-Channel Amplifier is built to power all your door speakers in a single, powerful package.

• Class-Leading Power

  • Class D full-range channels for lower current draw and longer playing time

  • Variable 12dB crossovers for ideal speaker matching

  • KickEQ™ variable bass boost for louder low frequencies

  • KICKER FIT™ (Fail-safe Integration Technology) means it works with nearly every radio

  • Small footprint for easy installation

  • Compatible with start/stop vehicle technology

  • DC-offset automatic turn on

  • Class SB-compatible for OEM integration within Class-SB head units

• Flexible and Fun

  This KICKER amp features a variable bass boost with KickEQ™, giving you as much as a 6dB of extra bump.  KICKER’s FIT™ (Fail-safe Integration Technology), gives you outstanding noise rejection - even with premium factory audio systems.

• Specifications

  Power (watts/ch), 2 Ohm Stereo:75 x 4 Power (watts/ch), 4 Ohm Stereo:50 x 4 Power (watts/ch), 4 Ohm Bridged Mono:150 x 2 Dynamic Power (watts):350 Frequency Response (Hz):10-20k(+0/-1dB) Dimensions (in, cm):Height: 2-3/16 (5.6 cm) Width: 5-29/32 (15 cm) Length: 8-25/32 (22.3 cm)

  Input Sensitivity:125mV-10V Signal-to-Noise Ratio:>95dB (A-weighted, re: rated power) Selectable Electronic Crossover:Off/HP/LP, variable 50-200Hz @ 12dB/octave KickEQ Bass Boost:variable 0-6dB @ 40Hz

• Warranty When purchased from an Authorized KICKER Dealer or kicker.com, KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase.

‍ ‍Class D 4-Channel Power Amplifier

• Max Power 600W

• RMS 50W x4 (4Ω)

• RMS 75W x4 (2Ω)

• RMS 150W x 2 (Bridged)

• Size (inch) (W) 8-3/8" x (H) 2-1/16" x (D) 5-7/8"

• High-Resolution Audio Certified

• Variable High & Low Pass Filter

• Bass Boost

• • Max Power 1000W

  • RMS 300W (4Ω)

  • RMS 500W (2Ω)

  • Size (inch) (W) 8-3/8" x (H) 2-1/16" x (D) 5-7/8"

  • Variable Low Pass Filter

  • Bass Boost

  • Infrasonic Filter

  • Wired Remote Included

Class D 5-Channel Power Amplifier

• Max Power 1600W

• RMS 50W x4 + 300W (4Ω)

• RMS 75W x4 + 500W (2Ω)

• RMS 150W x 2 (Bridged) + 300W (4Ω)

• Size (inch) (W) 9-3/4" x (H) 2-1/16" x (D) 6-5/8"

• High-Resolution Audio Certified

• Variable High & Low Pass Filter

• Bass Boost

• Wired Remote Included

Cta-2006 Compliant

Number of Channels

1

Total Power
(Sum of Rated Power)

500 Watts

Rated Power
(RMS Continuous Power)

300 Watts x 1 @ 4Ω
500 Watts x 1 @ 2Ω

Dynamic Power
(PVC/PowerCube®)

350 Watts x 1 @ 4Ω
590 Watts x 1 @ 2Ω

Bridgeable

No

Frequency Response

20 Hz - 250 Hz

Input Sensitivity

Low-Level: 150 mV - 4 V
High-Level: 450 mV - 12 V

Circuit Topology Class

Class-D

Efficiency (average)

Total Harmonic Distortion (THD+Noise)

4Ω: <1.0%
2Ω: <1.0%

Signal Input

Low-Level: 2 RCA
High-Level: 4-Pin Molex

Signal Output

Low-Level: 2 RCA
(Pass-Thru active with RCA or Hi-Level input)

Tone Controls

0 to +18 dB @ 45 Hz

Crossover Controls

Low-Pass:
50 Hz - 250 Hz @ 12dB/Octave Butterworth

Infrasonic:
15 Hz - 40 Hz @ 12dB/Octave Butterworth

Remote Controls

Yes

Visual Indicators

Power/Protect
C.L.E.A.N. In
C.L.E.A.N. Out

Power Wire Gauge

4 AWG

Power Input Connector

Compression Terminal Block

Speaker Wire Gauge

8 AWG

Speaker Output Connector

Compression Terminal Block

Cooling

Convection

Heatsink

Operating Voltage

9 - 16 VDC

Recommended Fuse
(not included)

80 A

Average Current Draw (13.8V Music)

Max. Current Draw (13.8V Sinewave)

52 A

Suggested Alternator

Included In The Box

Dimensions (H x W x D)

1.9" x 6.8" x 8.5"
(4.9 cm x 17.3 cm x 21.5 cm)

Cta-2006 Compliant

Number of Channels

1

Total Power
(Sum of Rated Power)

250 Watts

Rated Power
(RMS Continuous Power)

160 Watts x 1 @ 4Ω
250 Watts x 1 @ 2Ω

Dynamic Power
(PVC/PowerCube®)

209 Watts x 1 @ 4Ω
328 Watts x 1 @ 2Ω

Bridgeable

No

Frequency Response

20 Hz - 250 Hz

Input Sensitivity

Low-Level: 150 mV - 4 V
High-Level: 450 mV - 12 V

Circuit Topology Class

Class-D

Efficiency (average)

Total Harmonic Distortion (THD+Noise)

4Ω: <1.0%
2Ω: <1.0%

Signal Input

Low-Level: 2 RCA
High-Level: 4-Pin Molex

Signal Output

Low-Level: 2 RCA
(Pass-Thru active with RCA or Hi-Level input)

Tone Controls

0 to +18 dB @ 45 Hz

Crossover Controls

Low-Pass:
50 Hz - 250 Hz @ 12dB/Octave Butterworth

Infrasonic:
15 Hz - 40 Hz @ 12dB/Octave Butterworth

Remote Controls

Yes

Visual Indicators

Power/Protect
C.L.E.A.N. In
C.L.E.A.N. Out

Power Wire Gauge

4 AWG

Power Input Connector

Compression Terminal Block

Speaker Wire Gauge

8 AWG

Speaker Output Connector

Compression Terminal Block

Cooling

Convection

Heatsink

Operating Voltage

9 - 16 VDC

Recommended Fuse
(not included)

50 A

Average Current Draw (13.8V Music)

Max. Current Draw (13.8V Sinewave)

30 V

Suggested Alternator

Included In The Box

Dimensions (H x W x D)

1.9" x 6.8" x 8.1"
(4.9 cm x 17.3 cm x 20.5 cm)

Cta-2006 Compliant

Number of Channels

5

Total Power
(Sum of Rated Power)

750 Watts

Rated Power
(RMS Continuous Power)

50 Watts x 4 + 200 Watts x 1 @ 4Ω
100 Watts x 4 + 350 Watts x 1 @ 2Ω
200 Watts x 2 + N/A @ 4Ω Bridged/Mono

Dynamic Power
(PVC/PowerCube®)

70 Watts x 4 + 241 Watts x 1 @ 4Ω
114 Watts x 4 + 426 Watts x 1 @ 2Ω
234 Watts x 2 + N/A @ 4Ω Bridged/Mono

Bridgeable

Yes

Frequency Response

20 Hz - 20 kHz

Input Sensitivity

Low-Level: 150 mV - 4 V
High-Level: 450 mV - 12 V

Circuit Topology Class

Class-D

Efficiency (average)

Total Harmonic Distortion (THD+Noise)

Front/Rear 4Ω: <1.0%
Front/Rear 2Ω: <1.0%
Sub 4Ω: <1.0%
Sub 2Ω: <1.0%

Signal Input

Front Low-Level: 2 RCA
Front High-Level: 4-Pin Molex
Rear Low-Level: 2 RCA
Rear High-Level: 4-Pin Molex
Sub Low-Level: 2 RCA
Sub High-Level: 4-Pin Molex

Input Switch: 2/4/5 Input
(works for RCA/Hi-Level inputs)

Signal Output

N/A

Tone Controls

0 to +18 dB @ 45 Hz

Crossover Controls

Front High-Pass:
50 Hz - 250 Hz @ 12dB/Octave Butterworth

Front Low-Pass:
50 Hz - 250 Hz @ 12dB/Octave Butterworth

Rear High-Pass:
50 Hz - 250 Hz @ 12dB/Octave Butterworth

Rear Low-Pass:
50 Hz - 250 Hz @ 12dB/Octave Butterworth

Sub Low-Pass:
50 Hz - 250 Hz @ 12dB/Octave Butterworth

Sub Infrasonic:
15 Hz - 40 Hz @ 12dB/Octave Butterworth

Remote Controls

Yes

Visual Indicators

Power/Protect
C.L.E.A.N. In
C.L.E.A.N. Out (front)
C.L.E.A.N. Out (rear)
C.L.E.A.N. Out (sub)

Power Wire Gauge

4 AWG

Power Input Connector

Compression Terminal Block

Speaker Wire Gauge

8 AWG

Speaker Output Connector

Compression Terminal Block

Cooling

Convection

Heatsink

Operating Voltage

9 - 16 VDC

Recommended Fuse
(not included)

120 A

Average Current Draw (13.8V Music)

Max. Current Draw (13.8V Sinewave)

71 A

Suggested Alternator

Included In The Box

Dimensions (H x W x D)

1.9" x 6.8" x 11.2"
(4.9 cm x 17.3 cm x 28.5 cm)

Cta-2006 Compliant

Number of Channels

1

Total Power
(Sum of Rated Power)

750 Watts

Rated Power
(RMS Continuous Power)

250 Watts x 1 @ 4Ω
500 Watts x 1 @ 2Ω
750 Watts x 1 @ 1Ω

Dynamic Power
(PVC/PowerCube®)

300 Watts x 1 @ 4Ω
545 Watts x 1 @ 2Ω
830 Watts x 1 @ 1Ω

Bridgeable

No

Frequency Response

20 Hz - 250 Hz

Input Sensitivity

Low-Level: 150 mV - 4 V
High-Level: 450 mV - 12 V

Circuit Topology Class

Class-D

Efficiency (average)

Total Harmonic Distortion (THD+Noise)

4Ω: <1.0%
2Ω: <1.0%
1Ω: <1.0%

Signal Input

Low-Level: 2 RCA
High-Level: 4-Pin Molex

Signal Output

Low-Level: 2 RCA
(Pass-Thru active with RCA or Hi-Level input)

Tone Controls

0 to +18 dB @ 45 Hz

Crossover Controls

Low-Pass:
50 Hz - 250 Hz @ 12dB/Octave Butterworth

Infrasonic:
15 Hz - 40 Hz @ 12dB/Octave Butterworth

Remote Controls

Yes

Visual Indicators

Power/Protect
C.L.E.A.N. In
C.L.E.A.N. Out

Power Wire Gauge

4 AWG

Power Input Connector

Compression Terminal Block

Speaker Wire Gauge

8 AWG

Speaker Output Connector

Compression Terminal Block

Cooling

Convection

Heatsink

Operating Voltage

9 - 16 VDC

Recommended Fuse
(not included)

120 A

Average Current Draw (13.8V Music)

Max. Current Draw (13.8V Sinewave)

71 A

Suggested Alternator

Included In The Box

Dimensions (H x W x D)

1.9" x 6.8" x 10.1"
(4.9 cm x 17.3 cm x 25.5 cm)